Featured

RC car Brushless ESC, RC Race Car Brushless ESC

GT-8102 High Power Hot Air Rework Station

Posted on 11 September 2018

  • LCD display making parameters monitorable and system setting easier.
  • Pluggable design making handle and heater change easier.
  • Equip with vacuum suction pen, components can be extracted after desoldering.
  • Installed brushless fan, air volume can reach 120 l/min.
  • 1000W high power heating core make it heating up fast to reach the specified temperature.
  • PID algorithm controlled temperature accurate and stable.
  • Support timing/manual heating mode
  • Password protecting function make parameter setting with permission.
  • 3 sets of shortcut air volume/temperature data make it work more convenient.
  • Functions of temperature compensation, fixed temperature, upper and lower temperature limits making temperature’s management easier.
  •  Automatic standby/air delay after power- off function makes work safer.

kerui alarm

FMS RC airplane

Freewing Rc airplane

Sky flight hobby

soldering tools

Comments Off

RC Boat Brushless ESC, RC car Brushless ESC, RC Race Car Brushless ESC

AT938D 60W Digital & Lead-free Soldering Station

Posted on 11 September 2018

      • 
        

         

 

 

  • 
    
  • Temperature read out in ℃ and ℉
  • On/Off switch on the right side of the unit.
  • MCU controlled temperature calibration.
  • Simulate bar indicating heating up status.
  • LCD display screen making control visualization.
  • User-friendly menu enables system setting easier.
  • Separate iron stand to save room and to make easier deposit.
  • Buttons (1, 2, 3) for pre-setting or switching frequently used temperature.
  • Low-voltage heater separated from power supply to keep soldering work safer.
  • Soldering tip designed separate from heater and using exchangeable 900M series to save use-cost.

kerui alarm

FMS RC airplane

Freewing Rc airplane

Sky flight hobby

soldering tools

Comments Off

RC car Brushless ESC, RC Race Car Brushless ESC

150W High Frequency Soldering Station

Posted on 07 August 2018

Smart recognition of working or non-working status
Automatic standby, shutdown with smart time setting
High frequency eddy heating element, fast heating-up, thermal recovery and high thermal capacity.
Temperature locking.
Beep alarm function available.
Temperature read out in ℃ and ℉
MCU controlled temperature calibration.
Simulate bar indicating heating up status. fms airplane 
User-friendly menu enables system setting easier.
Separate iron stand to save room and to make easier deposit.
New design with LCD display screen making control visualization.
Buttons (1, 2, and 3) for pre-setting or switching frequently used temperature.
Temperature up to 500℃ for high thermal capacity required circumstances.
Low-voltage heater separated from power supply to keep soldering work safer.
Soldering tip designed separate from heater and using exchangeable AT500 series to save use-cost.

http://www.atten.com/project/at315dh/

 

Comments Off

ZTW Brushless ESC

50 Adjustable & Constant Temperature Soldering Iron

Posted on 16 July 2018

Description
Parameter
Soldering Tips
Soldering Accessories
Manual
High performance four-core wire PTC ceramic heater
Temperature in ℃ and ℉
Temperature up to 500℃ making it versatile
Manual temperature calibration by knob controlling
High efficiency of heating to reduce energy consumption.
Heat and fire resistant material handle set with light, slender and ergonomic design.
Soldering tip designed separate from heater and using exchangeable 900M series to save use-cost.
Grounded 3 core power cord and ESD safe design to minimize damage to user and sensitive electronic components.

more info:http://www.atten.com/project/sa-50/

Comments Off

RC Boat Brushless ESC, RC car Brushless ESC, RC Race Car Brushless ESC

60W Intelligent & Lead-free Soldering Station

Posted on 12 July 2018

● High performance dual-core ceramic heater.
● Smart recognition of working or non-working status.
● Automatic standby, shutdown with smart time setting.
● Temperature locking.
● Beep alarm function available.
● Temperature read out in ℃ and ℉
● MCU controlled temperature calibration.
● Simulate bar indicating heating up status.
● User-friendly menu enables system setting easier.
● Separate iron stand to save room and to make easier deposit.
● New design with LCD display screen making control visualization.
● Buttons(1,2,3) for pre-setting or switching frequently used temperature.
● Low-voltage heater separated from power supply to keep soldering work safer.
● Soldering tip designed separate from heater and using
● Exchangeable 900M series to save use-cost.

soldering station

Hot Air Station

rework station

soldering iron

soldering iron tools

Comments Off

RC car Brushless ESC, RC Race Car Brushless ESC, ZTW Brushless ESC

ZTW Gecko 85A Aircraft ESC 8A SBEC

Posted on 25 February 2018

This is a high-quality, efficient brushless electronic speed control with an integrated switch-mode BEC. It can operate without the need for a separate receiver battery to power your servos and receivers, saving you weight and complication. GECKO series also include ESC OPTO for giant flying. This series of ESCs also features an exposed, finned heat sink aluminum case with lightweight plastic end caps. Additional features include safe power arming along with advanced programmable, data logging system, low voltage cutoff, braking, timing, throttle input range, and more, making this series truly a pro series speed control.

As the development of the electronic and popular demand of the market, our BEC has been specifically designed RC airplane  for extreme aerobatics and therefore has the capability to support the higher current applications to eliminate the possibility of unwanted shutdowns, and is also capable of supporting continuous simultaneous multiple servo operations typically found in CCPM equipped hardcore 3D E-helicopters.

Features
Data logging system such as temperature, voltage, current, RPM,
SBEC Voltage Output 5.0, 6.0, 7.4, 8.4V adjustable
Advanced Governor Mode and soft start
High SBEC Current Output, continuous 8A and burst 16A, designed to meet your high current application
Power arm protection, over-heat protection, low-voltage protection and lost-signal protection
Secondary sub-menu setting by LCD program card or PC interface
Firmware updating by PC interface
Unique metal shape designing gives your new fashion visual impact.
Super smooth and accurate throttle linearity
Support and match with most of the motors, including high RPM motors
Programmable motor timing
Utilizes new smaller MOSFET technology to minimize weight
Finned heat sink
programmable throttle input range
Anti-spark circuit eliminates (HV OPTO version only)

Specifications
Output: Continuous Current 85A, Burst Current 100A for 10 seconds
Battery : 5-18 NiXX / 2-6S LiPo
Weight: 75g
BEC: 5.0V, 6.0V, 7.4V, 8.4V adjustable/8A
Size: 33x66x16mm (WxLxH)

Comments Off

RC Boat Brushless ESC, RC car Brushless ESC, ZTW Brushless ESC

ZTW Mantis 85A OPTO 2085031 for Rc Airplane

Posted on 16 January 2018

ZTW Mantis Series ESCs are designed for both beginner and advanced modelers. Their performance and stability have been approved by distributors and pilots around the world. Mantis ESCs feature a compact size, light weight, super smooth start up and throttle linearity, multiple protection modes, solid BEC output, and more. All these features make Mantis Series ESCs the perfect mid-level speed controller for park flyer, sport, and aerobatic pilots.

ZTW speed controllers are one of the most widely used and trusted speed controller brands available on the market today. They are sold under many different brand names, but we choose to purchase direct from the manufacturer without rebranding so that we can pass the savings on to you. ZTW controllers represent a new generation of brushless ESCs using advanced microprocessor technology. They are designed and manufactured with high quality components which provide exceptional reliability, low internal resistance, and a smooth, linear throttle response.

Features:
New advanced programming software with secondary sub-menu setting for ease of use.
Advanced Governor Mode (uses B-Series design to keep the motor speed even though the load is changed)
Supports high RPM motors, can be used with most of the RC motors on the market.
More optional motor timing, startup and soft acceleration settings for smoother motor operation.
Super smooth and accurate throttle linearity.
Power arming protection (prevents the motor from accidentally running when switched ON).
Auto throttle shut down in signal loss situation.
Safety thermal over-load protection: when the temperature of ESC exceeds 110 deg C, the ESC will reduce the output power to allow it to cool.
Uses new generation MOSFET to ensure ESC’s low operation temperature while supporting biggest peak currents and higher reliability.

Specifications:
Output: 85A continuous, 100A burst for 10 seconds
Input voltage: 2-6s LiPo; 5-18 cell Ni-XX
Weight: 53g
Dimensions: 47 x 35 x 15mm
NO BEC

Programmable Options:
Brake setting (off/soft/mid/hard — default: off)
Battery type: (Ni-XX/LiPo/LiFe — default: LiPo auto detect)
Low voltage cutoff setting (2.8V / 3.0V / 3.2V / None — default: 3.0V)
Factory default setup reset
Timing settings (auto / 2° / 5° / 8° /15° / 22° /30° — default: auto)
SBEC output voltage (on 45A and larger models only) (5.0V / 5.5V / 6.0V — default: 5.0V)
Governor mode (RPM off / 1st soft start / 2nd soft start / gov mod 1 / gov mod 2 — default: RPM off)
Motor rotation (forward / reverse — default: forward)
Start-up strength (10% / 15% / 20% / 25% / 30% / 35% / 40% / 45% / 50% — default: 30%)
Low voltage cutoff type: )reduce power / cut-off power — default: reduce)

Parameters can be programmed using your transmitter, or by using the optional programming card sold separately.

Comments Off

RC Boat Brushless ESC, RC car Brushless ESC, RC Race Car Brushless ESC, ZTW Brushless ESC

ZTW Mantis 85A SBEC 2085201 for Rc airplane

Posted on 16 January 2018

ZTW speed controllers are one of the most widely used and trusted speed controller brands available on the market today. They are sold under many different brand names, but we choose to purchase direct from the manufacturer without rebranding so that we can pass the savings on to you. ZTW controllers represent a new generation of brushless ESCs using advanced microprocessor technology. Freewing RC airplane  They are designed and manufactured with high quality components which provide exceptional reliability, low internal resistance, and a smooth, linear throttle response.

Features:
New advanced programming software with secondary sub-menu setting for ease of use.
Advanced Governor Mode (uses B-Series design to keep the motor speed even though the load is changed)
Supports high RPM motors, can be used with most of the RC motors on the market.
More optional motor timing, startup and soft acceleration settings for smoother motor operation.
Super smooth and accurate throttle linearity.
Power arming protection (prevents the motor from accidentally running when switched ON).
Auto throttle shut down in signal loss situation.
Safety thermal over-load protection: when the temperature of ESC exceeds 110 deg C, the ESC will reduce the output power to allow it to cool.
Uses new generation MOSFET to ensure ESC’s low operation temperature while supporting biggest peak currents and higher reliability.

Specifications:
Output: 85A continuous, 100A burst for 10 seconds
Input voltage: 2-6s LiPo; 5-18 cell Ni-XX
SBEC output: 5.0V / 5.5V / 6.0V adjustable @ 5A (switching)
Weight: 57g Dimensions: 47 x 35 x 15mm

Programmable Options:
Brake setting (off/soft/mid/hard — default: off)
Battery type: (Ni-XX/LiPo/LiFe — default: LiPo auto detect)
Low voltage cutoff setting (2.8V / 3.0V / 3.2V / None — default: 3.0V)
Factory default setup reset
Timing settings (auto / 2° / 5° / 8° /15° / 22° /30° — default: auto)
SBEC output voltage (on 45A and larger models only) (5.0V / 5.5V / 6.0V — default: 5.0V)
Governor mode (RPM off / 1st soft start / 2nd soft start / gov mod 1 / gov mod 2 — default: RPM off)
Motor rotation (forward / reverse — default: forward)
Start-up strength (10% / 15% / 20% / 25% / 30% / 35% / 40% / 45% / 50% — default: 30%)
Low voltage cutoff type: )reduce power / cut-off power — default: reduce)

Parameters can be programmed using your transmitter, or by using the optional programming card sold separately.

 

 

 

Comments Off

RC car Brushless ESC, RC Race Car Brushless ESC, ZTW Brushless ESC

ZTW Mantis 90A OPTO 2090411 for Rc airplane

Posted on 16 January 2018

This is a high voltage version ESC supports 6S to 12S LiPo batteries but without BEC.

ZTW Mantis Series ESCs are designed for both beginner and advanced modelers. Their performance and stability have been approved by distributors and pilots around the world. Mantis ESCs feature a compact size, light weight, super smooth start up and throttle linearity, multiple protection modes, solid BEC output, and more. All these features make Mantis Series ESCs the perfect mid-level speed controller for park flyer, sport, and aerobatic pilots.

ZTW speed controllers are one of the most widely used and trusted speed controller brands available on the market today. They are sold under many different brand names, but we choose to purchase direct from the manufacturer without rebranding Rc airplane so that we can pass the savings on to you. ZTW controllers represent a new generation of brushless ESCs using advanced microprocessor technology. They are designed and manufactured with high quality components which provide exceptional reliability, low internal resistance, and a smooth, linear throttle response.

Features:
New advanced programming software with secondary sub-menu setting for ease of use.
Advanced Governor Mode (uses B-Series design to keep the motor speed even though the load is changed)
Supports high RPM motors, can be used with most of the RC motors on the market.
More optional motor timing, startup and soft acceleration settings for smoother motor operation.
Super smooth and accurate throttle linearity.
Power arming protection (prevents the motor from accidentally running when switched ON).
Auto throttle shut down in signal loss situation.
Safety thermal over-load protection: when the temperature of ESC exceeds 110 deg C, the ESC will reduce the output power to allow it to cool.
Uses new generation MOSFET to ensure ESC’s low operation temperature while supporting biggest peak currents and higher reliability.

Specifications:
Output: 90A continuous, 120A burst for 10 seconds
Input voltage: 6-12s LiPo; 18-38 cell Ni-XX
Weight: 128g
Dimensions: 80 x 48 x 21mm

Programmable Options:
Brake setting (off/soft/mid/hard — default: off)
Battery type: (Ni-XX/LiPo/LiFe — default: LiPo auto detect)
Low voltage cutoff setting (2.8V / 3.0V / 3.2V / None — default: 3.0V)
Factory default setup reset
Timing settings (auto / 2° / 5° / 8° /15° / 22° /30° — default: auto)
SBEC output voltage (on 45A and larger models only) (5.0V / 5.5V / 6.0V — default: 5.0V)
Governor mode (RPM off / 1st soft start / 2nd soft start / gov mod 1 / gov mod 2 — default: RPM off)
Motor rotation (forward / reverse — default: forward)
Start-up strength (10% / 15% / 20% / 25% / 30% / 35% / 40% / 45% / 50% — default: 30%)
Low voltage cutoff type: )reduce power / cut-off power — default: reduce)

Comments Off

RC Boat Brushless ESC, RC car Brushless ESC, ZTW Brushless ESC

ZTW Seal 300A OPTO HV 14S for Rc boat

Posted on 10 January 2018

We all know that that boaters crave for more power than cars and airplanes and ZTW has come up with a whole new way to put the power to the water – The new SEAL line water-cooling brus

 

hless speed controls for marine applications. ZTW uses new FETS that offer less resistance and less heat dissipated. Even so they added more water-pipes to increase the cooling area to dissipate the heat faster and better so as to bring a even more incredible power levels without any risk of frying the controller.

Well designed MCU with efficient code makes for faster sync and accurate control. Beside the performance they have also bring you a whole new fashion looking marine ESC.

This is their SEAL marine speed controller. Quality, performance and fashion are what they are all about.

Features:
1. Extremely low internal resistance
2. High efficient three pipe water cooling system
3. Super smooth and accurate throttle linearity
4. Over temperature protection
5. Auto throttle shut down in signal lose situation
6. Supports high RPM motors
7. Power arming protection (prevents the motor from accidentally running when switched ON)
8. New Advanced programming software

Specifications:
Continuous Current – 300A
Burst Current (10s) – 180A
Battery – 5-18 NC/2-6 LiPo
BEC Output – 5.5V/3A
Width – 65mm
Length – 46mm
Height – 23..5mm
Weight – 780g

ZTW Brushless ESC 

more info:  http://www.ztwshop.com

Comments Off

SEE MORE ARTICLES IN THE ARCHIVE

Advertise Here
Advertise Here

Get your own free Online Shop at shop-worlds.com